Selectron LD-007 Manual de Instruções Página 222
- Página / 368
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
212
send data to a node on the same Subsystem (i.e., network). Refer to the
SYSMAC NET Link System Manual for details.
Word Bits 00 to 07 Bits 08 to 15
C Number of words (0 to 1000 in 4-digit hexadecimal, i.e., 0000
hex
to 03E8
hex
)
C+1 Network number (0 to 127 in 2-digit
hexadecimal, i.e., 00
hex
to 7F
hex
)
Bit 14 ON: Operating level 0
OFF: Operating level 1
Bits 08 to 13 and 15: Set to 0.
C+2 Destination node (0 to 126 in 2-digit
hexadecimal, i.e., 00
hex
to 7E
hex
)*
Destination port
NSB: 00
NSU: 01/02
*The node number of the PC executing the send may be set.
SYSMAC LINK Systems Set the destination node number to 0 to send the data to all nodes. Refer to
the SYSMAC LINK System Manual for details.
Word Bits 00 to 07 Bits 08 to 15
C Number of words (0 to 256 in 4-digit hexadecimal, i.e., 0000
hex
to 0100
hex
)
C+1 Response time limit (0.1 and 25.4
seconds in 2-digit hexadecimal
without decimal point, i.e., 00
hex
to
FF
hex
)
Note: The response time will be
2 seconds if the limit is set to 0
hex
.
There will be no time limit if the
time limit is set to FF
hex
.
Bits 08 to 11:
No. of retries (0 to 15 in
hexadecimal,
i.e., 0
hex
to F
hex
)
Bit 12: Set to 0.
Bit 13 ON: Response not returned.
OFF: Response returned.
Bit 14 ON: Operating level 0
OFF: Operating level 1
Bit 15: Set to 1.
C+2 Destination node (0 to 62 in 2-digit
hexadecimal, i.e., 00
hex
to 3E
hex
)*
Set to 0.
*The node number of the PC executing the send cannot be set.
Examples This example is for a SYSMAC NET Link System. When 00000 is ON, the
following program transfers the content of IR 001 through IR 005 to LR 20
through LR 24 on node 10.
0005
0000
000A
IR 001
IR 002
IR 003
IR 004
IR 005
LR 20
LR 21
LR 22
LR 23
LR 24
DM 0010
DM 0011
DM 0012
15 0
SEND(90)
001
LR 20
DM 0010
00000
Node 10
Address Instruction Operands
00000 LD 00000
00001 SEND(90)
001
LR 20
DM 0010
Flags ER: The specified node number is greater than 126 in a SYSMAC NET
Link System or greater than 62 in a SYSMAC LINK System.
The sent data overruns the data area boundaries.
SYSMAC NET Link/SYSMAC LINK Instructions Section 5-23
- (CPU01-E/03-E/11-E) 1
- OMRON Product References 2
- Visual Aids 2
- TABLE OF CONTENTS 3
- About this Manual: 6
- PRECAUTIONS 7
- 1 Intended Audience 8
- 2 General Precautions 8
- 3 Safety Precautions 8
- 5 Application Precautions 9
- 5Application Precautions 10
- SECTION 1 12
- Introduction 12
- 1-1 Overview 13
- 1-2 The Origins of PC Logic 13
- 1-3 PC Terminology 14
- 1-4 OMRON Product Terminology 15
- 1-5 Overview of PC Operation 15
- 1-6 Peripheral Devices 16
- 1-7 Available Manuals 18
- 1-8 LSS Capabilities 19
- 1-8-2 Online Operations 20
- LSS Capabilities Section 1-8 21
- SECTION 2 22
- Hardware Considerations 22
- 2-1 Indicators 23
- 2-2 PC Configuration 23
- PC Configuration Section 2-2 24
- SECTION 3 25
- Memory Areas 25
- 3-1 Introduction 26
- 3-2 Data Area Structure 26
- Bit number 27
- IR word 000 0000000000000000 27
- IR word 001 0000000000000000 27
- 3-3 IR (Internal Relay) Area 28
- IR Area Section 3-3 29
- 3-4 SR (Special Relay) Area 30
- SR Area Section 3-4 31
- 3-4-1 Remote I/O Systems 32
- Host Link Systems 33
- PC Link Systems 35
- 3-4-4 I/O Status Hold Bit 38
- 3-4-5 Output OFF Bit 39
- 3-4-12 Step Flag 41
- 3-4-14 Arithmetic Flags 41
- AR Area Section 3-5 42
- (CPU11-E only) 45
- 3-5-8 Power-OFF Counter 46
- 3-6 DM (Data Memory) Area 48
- DM Area Section 3-6 49
- 3-7 HR (Holding Relay) Area 50
- 3-8 TC (Timer/Counter) Area 50
- 3-9 LR (Link Relay) Area 51
- 3-10 Program Memory 52
- SECTION 4 53
- 4-1 Basic Procedure 54
- 4-2 Instruction Terminology 54
- 4-3 Basic Ladder Diagrams 55
- 4-3-2 Mnemonic Code 56
- 4-3-3 Ladder Instructions 57
- A LOAD instruction 58
- A LOAD NOT instruction 58
- 4-3-4 OUTPUT and OUTPUT NOT 60
- 4-3-5 The END Instruction 60
- Program execution 61
- Instruction 62
- 00000 00001 62
- 00002 00003 62
- 4-4 The Programming Console 68
- 4-4-1 The Keyboard 69
- 4-4-2 PC Modes 70
- 4-5 Preparation for Operation 72
- 4-5-2 Buzzer 73
- 4-5-3 Clearing Memory 73
- 4-5-5 Clearing Error Messages 76
- 4-5-6 Verifying the I/O Table 76
- 4-5-7 Reading the I/O Table 77
- 4-5-8 Clearing the I/O Table 79
- 4-5-9 NET Link Table Transfer 80
- 4-6-3 Checking the Program 86
- 4-6-5 Program Searches 89
- Original Program 91
- Diagram A: Correct Operation 93
- 4-6-8 Jumps 97
- 4-7 Controlling Bit Status 99
- Work Bits Section 4-8 100
- 4-9 Programming Precautions 102
- Diagram A: Incorrect 103
- Diagram B 103
- Diagram A 103
- 4-10 Program Execution 104
- Instruction Set 105
- SECTION 5 105
- 5-1 Notation 107
- 5-2 Instruction Format 107
- *DM 0001 108
- 5-6-2 AND LOAD and OR LOAD 113
- 5-7 Bit Control Instructions 114
- IR, AR, HR, LR 115
- 5-7-3 KEEP – KEEP(11) 116
- S execution condition 117
- R execution condition 117
- Status of B 117
- N: Jump number 120
- # (00 to 99) 120
- 5-10 END – END(01) 121
- 5-11 NO OPERATION – NOP(00) 122
- 5-12-1 TIMER – TIM 123
- N: TC number 127
- # (000 through 015 preferred) 127
- SV: Set value (word, BCD) 127
- IR, AR, DM, HR, LR, # 127
- 5-12-3 COUNTER – CNT 128
- # (000 through 511) 131
- 5-13 Data Shifting 133
- Data Shifting Section 5-13 134
- 5-13-5 ROTATE LEFT – ROL(27) 138
- 5-13-6 ROTATE RIGHT – ROR(28) 138
- 5-13-9 WORD SHIFT – WSFT(16) 140
- 5-14 Data Movement 142
- 5-14-2 MOVE NOT – MVN(22) 143
- Data Movement Section 5-14 144
- 5-14-5 BLOCK SET – BSET(71) 145
- 5-14-10 MOVE BIT – MOVB(82) 149
- 5-14-11 MOVE DIGIT – MOVD(83) 150
- 5-15 Data Comparison 151
- 5-15-2 COMPARE – CMP(20) 152
- Data Comparison Section 5-15 153
- 5-16 Data Conversion 159
- Data Conversion Section 5-16 160
- 5-17 BCD Calculations 172
- 5-17-1 INCREMENT – INC(38) 173
- 5-17-2 DECREMENT – DEC(39) 173
- 5-17-3 SET CARRY – STC(40) 173
- 5-17-4 CLEAR CARRY – CLC(41) 174
- 5-17-5 BCD ADD – ADD(30) 174
- BCD Calculations Section 5-17 175
- 5-17-7 BCD SUBTRACT – SUB(31) 176
- 5-17-9 BCD MULTIPLY – MUL(32) 181
- 5-17-11 BCD DIVIDE – DIV(33) 182
- 5-18 Binary Calculations 189
- Mi – Su – CY CY R 191
- 5-19 Logic Instructions 194
- 5-19-2 LOGICAL AND – ANDW(34) 195
- 5-19-3 LOGICAL OR – ORW(35) 195
- 5-20-1 Overview 197
- N: Subroutine number 198
- 5-21 Step Instructions 203
- Step controlled by LR 2000 204
- Step controlled by LR 2001 204
- Examples 205
- 5-22 Special Instructions 212
- 5-22-2 CYCLE TIME – SCAN(18) 213
- FAL(06) 00 215
- 5-22-6 SET SYSTEM – SYS(49) 216
- 5-22-7 BIT COUNTER – BCNT(67) 217
- Input data, x Result data 218
- Control Data 221
- SEND(90) 222
- RECV(98) 224
- SECTION 6 228
- Program Execution Timing 228
- 6-1 Cycle Time 229
- Cycle Time Section 6-1 230
- 6-1-2 CPU11-E Cycle Time 233
- 6-2 Calculating Cycle Time 235
- 6-2-2 PC with Link Units 236
- ÷ constant b word 239
- ÷ *DM b *DM 239
- ÷ word b word 240
- ÷ word b word (equals 0) 241
- 6-4 I/O Response Time 243
- I/O Response Time Section 6-4 244
- SECTION 7 245
- 7-1-1 Bit/Digit Monitor 246
- 7-1-2 Forced Set/Reset 249
- Word currently 252
- [ Data ] 252
- 7-1-6 3-word Monitor 254
- 3 words currently 255
- 7-1-8 Binary Monitor 256
- Indicates Force Reset 257
- Indicates Force Set 257
- Key Sequence 258
- IR bit 00115 IR bit 00100 259
- Returns to original display 261
- Current SV (during 261
- SV before the change 261
- SECTION 8 270
- Troubleshooting 270
- 8-1 Alarm Indicators 271
- 8-4 Error Messages 272
- Error Messages Section 8-4 273
- 8-5 Error Flags 275
- Error Flags Section 8-5 276
- Appendix A 277
- C200H I/O Units 278
- C200H Special I/O Units 279
- C200H Link Units 280
- Optional Products 281
- Optical Units 282
- Link Adapters 282
- DIN Products 282
- Optical Fiber Cable 283
- Cable Length 283
- Peripheral Devices 284
- Ladder Support Software (LSS) 284
- Appendix AStandard Models 285
- Appendix B 286
- Instruction Execution Times 289
- Basic Instructions 294
- Data Areas 295
- Special Instructions 296
- ≤ S ≤ Upper limit 1 308
- (SBs+Of) (D) 313
- Appendix C 319
- System Operations 320
- Programming Operations 322
- Cassette Tape Operations 327
- Appendix D 329
- Appendix E 332
- Dedicated Bits 333
- Appendix EData Areas 334
- AR Word Allocations 334
- AR Bit Allocations 334
- Data Areas Appendix E 335
- Appendix F 336
- I/O Bits 337
- Work Bits 338
- Data Storage 339
- Timers and Counters 340
- Appendix G 341
- Program Coding Sheet 342
- Appendix H 343
- Appendix I 344
- Glossary 345
- Revision History 367
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais